رقم الجزء
تجريد
صلاحيه
UOM
NIIN
TXT
وصف:
Nonmetallic Hose Assembly
MRC:
The style designation indicating the configuration that most nearly corresponds to the cross-sectional shape of the item.AAGR
Cross Sectional Shape:
Round
MRC:
The length of a straight line which passes through the center of a circular figure or body,and terminates at the inside circumference.AARX
Inside Diameter:
1.250 inches
MRC:
A value which expresses the degree of heat or cold as applied to the operation,or limitation of operation,of an item.ABJH
Tempurature Rating:
-67.0 degrees fahrenheit and 250.0 degrees fahrenheit single response
MRC:
A measurement of the smallest dimension of a flange,in distinction from length or width.ABKU
Flange Thickness:
0.310 inches and 0.320 inches 1st end
MRC:
The length of a straight line which passes through the center of a circular figure or body,and terminates at the outside circumference.ABKV
Outside Diameter:
2.000 inches
MRC:
The length of a straight line which passes through the center of the recess,and terminates at the circumference.ABMD
Recess Diameter:
1.125 inches 1st end
MRC:
A measurement between specified points on the recess,in distinction from height.ABMH
Recess Depth:
0.026 inches 1st end
MRC:
The minimum inside bending radius formed without stressing or deformation of a flexible item.ACKH
Minimum Inside Bending Radius:
16.000 inches
MRC:
The amount of rotation in a counterclockwise direction needed to bring the centerline of one rigid elbow into coincidence with the centerline of the rigid elbow on the opposite end,expressed in degrees.ADKX
Angle Between Rigid Elbow Fittings In Deg:
0.0
MRC:
The length of a straight line which passes through the center of the flange,and terminates at the outside circumference.AEPR
Flange Outside Diameter:
1.990 inches and 2.010 inches 1st end
MRC:
The style designation indicating the configuration that most nearly corresponds to the appearance of the connection.AHNC
Connection Style:
Recessed w/gasket groove 1st end
MRC:
The design used in constructing the end portion of the flange.AKUT
End Flange Construction:
Solid 1st end
MRC:
The physical configuration of the outside of the end connection.AKUU
End Connection Design:
Elbow 1st end
MRC:
Indicates the type of connection/s/.AWLS
Connection Type:
Recessed flange 1st end
MRC:
The minimum internal pressure rating,determined by destruction tests,at which the item can be expected to rupture.CQBD
Burst Test Pressure:
2500.0 pounds per square inch
MRC:
The material and formation identifying the structural characteristic/s/ of the item and location.CQCS
Layer Composition And Location:
1st layer braided steel wire and 2nd layer braided steel wire and outer layer molded rubber, chloroprene
MRC:
The maximum pressure at which the item is rated for operation.CQGM
Maximum Operating Pressure:
625.0 pounds per square inch
MRC:
A steady,uniform,internal,static pressure that the item must withstand without leakage,abnormal distortion,or damage.CRDW
Hydrostatic Test Pressure:
1250.0 pounds per square inch
MRC:
The angle that the flow is turned from the straight flow.CRFY
Flow Angle:
90.0 degrees 1st end
MRC:
The type of protection provided by the outer covering.CRJM
Outer Covering Environmental Protection:
Mildew resistant and oil resistant and oil resistant
MRC:
The condition of the item with respect to the texture of the inner surface.CRWL
Inside Surface Condition:
Smooth
MRC:
The means used and the measurement of the longest dimension of an item.CRXX
Measuring Method And Length:
215.000 inches working
MRC:
The style designation indicating the configuration that most nearly corresponds to the appearance of the flange.CTCJ
Flange Style:
Round w/ bolt holes 1st end
MRC:
The type of media for which the item is designed.MEDA
Media For Which Designed:
Fuel/oil, hydrocarbon single response
