رقم الجزء
تجريد
صلاحيه
UOM
NIIN
TXT
وصف:
Control Transformer Synchro
MRC:
The basic material of which the body is fabricated.AAFZ
Body Material:
Steel, corrosion resisting
MRC:
The style designation indicating the configuration that most nearly corresponds to the appearance of the body.AAQL
Body Style:
Standard round b
MRC:
The length of a straight line which passes through the center of a shoulder,and terminates at the circumference.AAVH
Shoulder Diameter:
Between 1.3070 inches and 1.3120 inches
MRC:
The length of a straight line which passes through the center of that portion used to guide the item and terminates at the circumference.AAVL
Pilot Diameter:
Between 0.8745 inches and 0.8750 inches
MRC:
The dimension measured along the longitudinal axis with terminated points at the extreme ends of the item.ABHP
Overall Length:
3.0830 inches
MRC:
The length of a straight line which passes through the center of a flange,and terminates at the circumference.ABKK
Flange Diameter:
Between 1.4320 inches and 1.4370 inches
MRC:
A measurement of the smallest dimension of a flange,in distinction from length or width.ABKU
Flange Thickness:
Between 0.0880 inches and 0.0980 inches
Undercut Width:
Between 0.0730 inches and 0.0830 inches
MRC:
The length of a straight line which passes through the center of a shaft,and terminates at the circumference.ABWV
Shaft Diameter:
0.1870 inches and 0.1872 inches single shaft
MRC:
A measurement of the longest dimension of the shaft,in distinction from width.ABXF
Shaft Length:
0.5450 inches and 0.5650 inches single shaft
MRC:
The maximum permissible temperature increase in the item as a result of its operation under normal conditions.AHCG
Maximum Tempurature Rise:
10.0 degrees celsius
MRC:
An alpha and/or numeric designation indicating the size by which the body is identified.AJSL
Body Size:
15
MRC:
The value of the primary excitation voltage for which the stator is rated,expressed in volts.AJSN
Stator Input Voltage Rating In Volts:
90.0
MRC:
The value of the primary excitation current for which the stator is rated,with rotor /secondary/ circuit open.AJSP
Stator Input Current Rating:
13.0 milliamperes
MRC:
The value of the primary /electrical/ excitation power for which the stator is rated.AJSQ
Stator Input Electrical Power Rating:
210.0 milliwatts
MRC:
The cycles per second /hertz/ of the alternating current.AJSS
Frequency In Hertz:
60.0
MRC:
The magnitude part /z/ of the stator impedance with the rotor open /zso/,expressed in ohms.AJTJ
Zso Impedance Magnitude In Ohms:
6250.00
MRC:
The angle part /o/ of the stator impedance with the rotor open /zso/,expressed in degrees.AJTK
Zso Impedance Angle In Deg:
Between 76.00 and 84.00
MRC:
The magnitude part /z/ of the rotor impedance with the stator shorted /zrs/,expressed in ohms.AJTL
Zrs Impedance Magnitude In Ohms:
1475.00
MRC:
The angle part /o/ of the rotor impedance with the stator shorted /zrs/,expressed in degrees.AJTM
Zrs Impedance Angle In Deg:
Between 12.00 and 20.00
MRC:
The difference between the phase time of two or more voltages or currents of the same frequency,at the same instant of time,expressed in degrees.AJVF
Phase Shift Angle In Deg:
9.000 input to output
MRC:
The maximum voltage,without harmonics,induced in the secondary circuit at the null angle rotor position,expressed in millivolts per volt.AJVG
Maximum Fundamental Null Voltage In Millivolts Per Volt:
50.00 output
MRC:
The maximum voltage,including harmonics,induced in the secondary circuit at the null angle rotor position,expressed in millivolts per volt.AJVH
Maximum Total Null Voltage Output In Millivolts Per Volt:
100.00
MRC:
The limits of permissible deviation in angular arc error from electrical zero,expressed in minutes.AJVL
Electrical Error Angular Range In Minutes:
-10.0 to 10.0
MRC:
The number of individual teeth on the splined portion of the shaft.AJVM
Spline Tooth Quantity:
21 single shaft
MRC:
The amount of rotary force that must be applied to the actuator to cause rotation,at plus 25 degrees celsius.AJVT
Actuator Friction Torque At Plus 25 Deg Celsius:
0.05 inch-ounces
MRC:
The number of holes provided for aligning the item.AJVW
Alignment Hole Quantity:
4
MRC:
The measurement taken from the bearing face to the point on the shaft where the weight /load/ is applied.AJWE
Shaft Radial Play Test Point:
0.125 inches
MRC:
The maximum shaft displacement perpendicular to the shaft axis due to reversal of a specified force applied perpendicular to the shaft axis,and measured at a specified distance from the front surface of the unit.AJWG
Shaft Maximum Radial Play:
0.0006 inches
MRC:
The axial shaft displacement due to reversal of a specified axial force,measured at the end of the shaft.AJWH
Shaft End Play:
Between 0.0005 inches and 0.0015 inches
MRC:
A measurement of the longest dimension of a pilot,in distinction from width.AJWQ
Pilot Length:
Between 0.0350 inches and 0.0450 inches
Shoulder Length:
Between 0.1070 inches and 0.1270 inches
Mounting Surface To Terminal End Distance:
2.5180 inches
MRC:
The number of teeth the splined shaft has per inch of pitch diameter.AJXA
Spline Tooth Diametral Pitch:
120 single shaft
MRC:
A designation distinguishing one group of shaft thread diameter-pitch combinations from another by the number of threads per measurement scale for a specific diameter.AJYY
Shaft Thread Series Designator:
Unf single shaft
MRC:
The direction of the shaft thread when viewed axially. a right-hand thread winds in a clockwise direction while a left-hand thread winds in a counterclockwise direction.AKAF
Shaft Thread Direction:
Right-hand single shaft
MRC:
A numeric-alpha designator indicating the ptich diameter tolerance,and an external or internal shaft thread.AKAN
Shaft Thread Class:
2a single shaft
MRC:
Indicates the location of the terminal/s/ on the item.CQTM
Terminal Location:
Rear
MRC:
A measurement of the extent of the shaft threads measured on a line parallel to the longitudinal axis.CQWQ
Shaft Thread Length:
0.2000 inches single shaft
MRC:
Indicates the type of shaft included on the item.CRSJ
Shaft Type:
Spline w/threads single shaft
Alignment Hole Depth:
0.1250 inches
MRC:
The ratio of the output voltage to the input voltage at maximum coupling.CSJY
Transformation Ratio:
0.735 rotor to stator
Alignment Hole Bolt Circle Diameter:
Between 1.0970 inches and 1.1030 inches
MRC:
The length of a straight line passing through the center of the shaft threaded portion,with terminated points at the circumference.CWBH
Shaft Thread Size:
0.190 inches single shaft
MRC:
The force (load) applied perpendicular to the shaft axis to determine radial play.CWXK
Shaft Radial Play Determining Weight:
8.0 ounces
MRC:
The force (load) applied parallel to the shaft axis to determine end play.CWYF
Shaft End Play Determining Weight:
16.0 ounces
MRC:
Indicates the type and number of terminals for providing electrical connection.TTQY
Terminal Type And Quantity:
5 screw
