رقم الجزء GS1006V4-11A

Close Tolerance Screw
توافر المخزون  رموز حالة المنتج

رقم الجزء gs1006v4-11a في المخزون بالكميات والشروط التالية.

  • NS: 1
  • NE: 2722

ملاحظة: تم آخر تحديث لتوفر هذا المنتج 08/28/2023 وربما تغيرت منذ ذلك الحين. اطلب عرض أسعار للأسعار المحدثة والتوافر.

الأسعار والتوافر

أرسل هذا النموذج لمعرفة الأسعار الحالية وتوافر NSN هذا.
رقم الجزء:
كم:
عنوان البريد الإلكتروني:
الهاتف:
مرجع:
شركة:
اسم:

نحن لا نشارك أو نبيع معلوماتك لأي شخص.
الخصوصيه | حيث

All major credit cards accepted as well as gov. p-cards

الصور

الصور المرجعية لهذا الجزء
صورة رقم المخزون الوطني 5305-01-462-2833

التسعير التاريخي لهذا المنتج هو بين 6.22 and 8.397 USD. اعتمادا على الكمية والتوافر والحالة والمهلة الزمنية والتوقف المحتمل للعنصر ، لا يمكننا ضمان التسعير حتى نقدم لك عرض أسعار محدث.

رقم الجزء
تجريد
صلاحيه
UOM
NIIN
رقم الجزء:
gs1006v4-11a
تجريد:
No
صلاحيه:
N/A
وحدة القياس:
1 EA
NIIN:
014622833

معلومات الجزء
Bolt, 100 degree tension head, gear drive recess

NSN
رقم المخزون الوطني:
5305-01-462-2833 5305014622833
TXT
وصف:
Close Tolerance Screw
INC
INC
رمز اسم العنصر:
29294
MRC:
A numeric-alpha designator indicating the pitch diameter tolerance and an external or internal thread.AAJD
Thread Class:
3a
MRC:
The direction of the thread when viewed axially. a right-hand thread winds in a clockwise direction while a left-hand thread winds in a counterclockwise direction.AAJF
Thread Direction:
Right-hand
MRC:
A measurement of the extent of threads,including incomplete threads,along a line parallel to the longitudinal axis.AASA
Thread Length:
0.425 inches
MRC:
The dimension,measured along a line parallel to the longitudinal axis,from the largest bearing surface of the fastener head to the extreme opposite end,or as specifically designated for other type fasteners.AASB
Fastener Length:
Between 1.098 inches and 1.128 inches
MRC:
The style designation indicating the configuration that most nearly corresponds to the appearance of the head.AASK
Head Style:
Flat countersunk undercut
MRC:
The length of a straight line which passes through the center of a circular head,and terminates at the circumference.AASL
Head Diameter:
Between 0.497 inches and 0.507 inches
MRC:
A measurement from the bottom to the top of the head,in distinction from depth.AASU
Head Height:
0.110 inches
MRC:
The length of a straight line which passes through the center of the smallest cross section of a spline,and terminates at the circumference.AAUH
Spline Minor Diameter:
Between 0.157 inches and 0.160 inches
MRC:
The length of a straight line which passes through the center of the largest cross section of a spline,and terminates at the circumference.AAUJ
Spline Major Diameter:
Between 0.220 inches and 0.223 inches
MRC:
The length of a straight line which passes through the center of the grip,and terminates at the circumference.AAUR
Grip Diameter:
Between 0.249 inches and 0.250 inches
MRC:
The style designation indicating the configuration that most nearly corresponds to the appearance of the internal drive.ABQZ
Internal Drive Style:
Torx
MRC:
The national stock number or the identification information of the end equipment for which the item is a part.AGAV
End Application:
Used on fa-18 e&f
MRC:
The nominal length of a straight line which passes through the center of the threaded portion,and terminates at the circumference.AHYM
Thread Diameter:
0.250 inches
MRC:
A measurement of the longest dimension of the grip,in distinction from width.ANEE
Grip Length:
0.688 inches
MRC:
The number of threads on the item per linear inch measured on a line parallel to the thread axis.CMLP
Thready Qty Per Inch (tpi):
28
MRC:
The maximum rated load in tension applied in a longitudinal direction,per unit of cross-sectional area,that the material can withstand without rupture.CQBC
Min. Tensile Strength (psi):
160000 pounds per square inch
MRC:
The included angle of the countersink.CRSQ
Countersink Angle:
Between 99.0 degrees and 101.0 degrees
MRC:
The chemical compound or mechanical mixture properties of which the item is fabricated.MATT
Material:
Titanium alloy
MRC:
A designation distinguishing one group of thread diameter-pitch combinations from another by the number of threads per measurement scale for a specific diameter.THSD
Thread Series Designator:
Unjf

{lang[cimilar]} Close Tolerance Screws

« Screws {lang[catalog]}
قارن الآن»
واضح | أخفى