رقم الجزء
تجريد
صلاحيه
UOM
NIIN
معلومات الجزء
Shaft, torque
TXT
وصف:
Shouldered Shaft
MRC:
The style designation indicating the configuration that most nearly corresponds to the appearance of the first end.AAGZ
First End Style:
Splined (straight)
MRC:
A term used to identify the ends as identical or not identical.AAHN
End Similarity:
Not identical
MRC:
The style designation indicating the configuration that most nearly corresponds to the appearance of the second end.AAHP
Second End Style:
Internal threaded
MRC:
The dimension measured along the longitudinal axis with terminated points at the extreme ends of the item.ABHP
Overall Length:
29.125 inches
MRC:
The national stock number or the identification information of the end equipment for which the item is a part.AGAV
End Application:
Los angeles class ssn
MRC:
The length of a straight line which passes through the center of the first end,and terminates at the circumference.AMDL
First End Diameter:
Between 4.9950 inches and 4.9980 inches
MRC:
A measurement of the longest dimension of the first end spline,in distinction from width.AMDM
First End Spline Length:
4.5000 inches
MRC:
The length of a straight line which passes through the center of the smallest circular cross section of the first end spline,and terminates at the circumference.AMDN
First End Spline Minor Diameter:
Between 5.0020 inches and 5.0050 inches
MRC:
The length of a straight line which passes through the center of the largest circular cross section of the first end spline,and terminates at the circumference.AMDP
First End Spline Major Diameter:
Between 5.4900 inches and 5.5000 inches
MRC:
The length of a straight line which passes through the center of the second end,and terminates at the circumference.AMFZ
Second End Diameter:
Between 4.9950 inches and 4.9980 inches
MRC:
A measurement of the extent of complete /full/ internal threads,along a line parallel to the longitudinal axis of the second end.AMHP
Second End Internal Thread Length:
0.870 inches
MRC:
The number of steps provided.ATPC
Step Quantity:
4
First End Spline Quantity:
20
MRC:
The length of a straight line which passes through the center of the largest step,and terminates at the circumference.CSPY
Largest Step Diameter:
Between 5.490 inches and 5.500 inches
MRC:
Designates the specific surface roughness rating,representing the arithmetic average deviation of the surface from the meanline in profile.CSYM
Surface Finish:
63.0 microinches
MRC:
Those unusual or unique characteristics or qualities of an item not covered in the other requirements and which are determined to be essential for identification.FEAT
Special Features:
Nha vls missile tube muzzle hatch
MRC:
The chemical compound or mechanical mixture properties of which the item is fabricated.MATT
Material:
Titanium alloy
MRC:
The specification,standard,or manufacturers reference,and the classification designation,such as class,condition,temper,and the like,that identifies the material.MDCL
Material Specification:
Mil-t-9047 aly ti-6al-4v, cond a military specification single material response
MRC:
Characteristics or qualities of an item,not covered in any other requirement,which are considered essential information for one or more functions excluding nsn assignment.SUPP
Supplementary Features:
First end has center jacking hole counterbored and threaded .500-13unc-2b: second end also has center hole and three (3) holes spaced 120 degrees on 3.750 dia. Centers; holes are countersunk 1.33 0.67 x 90 and threaded .625-11unc-2b to .87 min full thread: shaft has 2 splines; 1st end spline length 4.500 in., then 11.250 straight shaft, then second spline (same spline data) 5.00 in. Long, leaving 8.375 in. Straight shaft length 2nd end
